Battery Pack Features
- Digital Management Interface—LCD Display delivers battery operating status, voltage, amps, state of charge. Can also read cell voltages at the push of a
button for quick diagnostics - State of the art cell management:
- System – Automatically looks after battery health and operator safety. Fast acting circuit interrupter in case of short circuit, Low and high cell voltage protection, active temperature monitor, and solid state limiter switch. No contacts to wear out
- USB charge ports – 2 ports @ 2A each for charging electronics. Activated by panel button
- Separate charge port – for solar input or charging while in use
- T-Slotted extruded corners – Easy mounting of battery to vehicles or accessories to battery
- Rubber feet, handles, light mounts, DC accessories. Batteries are stackable
- Power saving sleep modes – Battery goes to sleep after a prescribed period of no use
- Service Port – Panel accessible port for programming, viewing history, or logging data
- Can be used as stand alone DC supply at 24VDC
- Nominal or to supply AC power through our pure sine wave inverters, 3500W continuous
- The ELECTRIX power pack is a high-end power solution for high-end equipment. Safe for all types of 120V, 50 or 60Hz, up to 25 Amperes continuous
Pure Sine Wave Inverters
- Digital Management Interface:
- LCD Display delivers battery operating status, voltage, amps, state of charge.
- Can also read cell voltages at the push of a button for quick diagnostics
- State of the art cell management:
- System – Automatically looks after battery health and operator safety. Fast acting circuit interrupter in case of short circuit, Low and high cell voltage protection, active temperature monitor, and solid state limiter switch. No contacts to wear out
- USB charge ports – 2 ports @ 2A each for charging electronics. Activated by panel button
- Separate charge port – for solar input or charging while in use
- T-Slotted extruded corners – Easy mounting of battery to vehicles or accessories to battery
- Rubber feet, handles, light mounts, DC accessories. Batteries are stackable
- Power saving sleep modes – Battery goes to sleep after a prescribed period of no use
- Service Port – Panel accessible port for programming, viewing history, or logging data
- Can be used as stand alone DC supply at 24VDC
- Nominal or to supply AC power through our pure sine wave inverters, 3500W continuous
- The ELECTRIX power pack is a high-end power solution for high-end equipment. Safe for all types of 120V, 50 or 60Hz, up to 25 Amperes continuous
Electrix Technical Specs
System Energy Information
| Nominal Energy: | 1.8kWh | 2.56kWh |
| Nominal Voltage: | 24VDC |
| Internal Resistance: | ≤ 0.40 mΩ |
| Max. Voltage Cutoff: | 28.8VDC |
| Min. Voltage Cutoff: | 21.6VDC |
| Max. Current Cutoff: | 100A @10sec | < 200A @10sec |
| Max. Inrush Current: | 600A @1/320th sec |
| Thermal Protection Cutoff: | 105°C (configurable) |
Discharge Information
| Max. Continuous Discharge Rate: | 72A | 150A |
| Recommended SOC Usage: | 10% - 90% |
| Built-In Control Switch: | Solid State FET 200A |
| Internal Built-In BMS Balancers |
Charging Information
| Charging Time (Standard): | 4 Hours |
| Separate Solid State Cutoff: | Solid State FET |
| Built-In Charge Control Switch: | Solid State FET 200A |
Power Savings Information
| Quiescent draw during sleep: | < 10uA @5V |
| Full EMS run-time mode: | 20 mA @5V |
Chemistry Information
-
Lithium Iron Phosphate LifePO4
-
Cycle Life (@ 80% of orig. capacity)
-
100 % DOD (1400) cycles
-
90 % DOD (1800) cycles
-
80 % DOD (2000) cycles +
Communication Options
-
Serial TTL Interface 8N1 57600 baud @5V
-
Other wired and wireless protocols are under development
5V USB Output Ports
-
Maximum Output 8A @5V
DataLogger
-
SD Card Logging MiniSD Card, 1GB – 64GB
-
Log charge/discharge/temp information in Voltage/Amps/Deg
EEPROM storage
-
Serial Number
-
Manufacture Date
-
Duty Cycles
-
Maximum Thresholds
